logosmall
 
GSM# 001299
White Stang
Modular 5.0

32900

points

Engine & Performance Modifications

updated: Feb 24th 2008 @ 05:49 PM

Engine & Performance Modifications
 
-302 Modular Stroker
 -Forged CP 17cc Dished Pistons
 -Forged Eagle H Beam Rods
-Forged stroker ModMax Crank
-Ported Heads
-Stage 2 Comp Cams
-ARP Hardware
-Melling high volume oil pump
-Moroso 7 quart oil pan
-FRPP 70mm Throttlebody
-Reichard Racing Intake
-SLP HTS SS Long Tubes
-SLP X Pipe
-SLP Loud Mouth 1 cat back
-Vortech T Trim
-2.85 8 rib Vortech blower Pulley
-MPH GI Joe's 8 rib pulley kit
-Aeromotive fuel rails
-Custom fuel lines 
-Anderson Power Pipe
-60 pound injectors
-Diablo Maf.ia
-Twin Cobra Fuel Pumps
-Kenne Belle Boost a pump
-Lightning 90MM Mass Air Meter
-Bar and plate Intercooler
-3" custom polished piping
-Oil Seperators custom install
-Battery Reloction(new)
-Battery Alternator disconect(new)
-New 1 gauge wiring(new)
 

 

 

 

 
 
 
 

 
 

 

 

 

 
Photo Sharing and Video Hosting at Photobucket Photo Sharing and Video Hosting at Photobucket Photo Sharing and Video Hosting at Photobucket Photo Sharing and Video Hosting at Photobucket Photo Sharing and Video Hosting at Photobucket
 
 
PowerTrain & Suspension
-PA SuperComp C4 with Transbrake
-4000 stall Torque Converter
-Cheetah Turbo Shifter 
-Diablosport Tuner
3.55 FRPP gears
-Moser 33 spline spool
-Moser 33 spline axles
-Moser c clip eliminators
-Moser 3" Wheel Studs
-TA 8.8 Axle support cover
-Strange adjustable shocks
-Strange adjustable Struts
-Welded axles
-Steeda lower control arms
-Steeda upper control arms
-Steeda Racing Hood Pins
-Drive Shaft Safety Loop
-Full Length Subframes
-UPR K Member
-UPR a Arms
-UPR Coil Overs
-Eibach Drag Springs
-UPR Bump Steer Kit
-UPR Caster Camber Plates
 

 
 
 
 
 

 

 
 
 
Engine pulled for new forged internals and 302 stroker kit.
 I pulled the motor to have new forged internals and 5.0 stroker kit installed. These are some picks of me pulling the motor in my garage. I think everyone should try this at least once.
 

Moroso 7 quart oil pan was installed
 to keep the oil cooler and to ensure
 the engine gets all the oil it needs.
The Anderson 4" power pipe drops
the air filter down just in front of
the passenger side front tire.
(equals cool air in a hot world) 

 

Pictures of Intercooler installed.
 Pictures don't show it but I had beeds welded on the pipes
 and installed t clamps in place of the worm clamps. Build your own! check it out in the HOWTOs!
 

 

http://www.free-musicvideocodes.com/asx.php?id=29127


 
SLP long tubes made A nice addition.
 Decided to install these when I reinstalled the engine.


 

 
Got oil in your intake? Check this out.
Oil seperators were added to stop oil flow back into the intake during WOT.I made some custom brackets to mount them behind the radiator overflow container. There is more details in the HOWTOs section.

 
 
Drive shaft safety loop.
The drive shaft safety loop was installed when they told me I could not run faster than 12.9 without it. After being explained what the DSSL does I quickly installed it. Car catapulting is not my thing nor do I want to share my cockpit with a driveshaft.
 
 
 
 
 
 
 
 
 
Brakes Painted
Brakes removed and painted red.
High heat ford red and clear paint were used.
 Moroso 3" wheel studs were installed.
 

 




Next Page


 
Page Listing
WHITE STANG99010 views
Engine & Performance Modifications3627 views
Exterior2422 views
Interior1780 views
Back to the track (1/4 mile vids)2291 views

Last 3 User Comments
mustangii
Aug 19th, 2008 @ 1:46 PM


“”
Replying to:

hey out there i just wanted to know if anyone ever had someplace do mounting and balanceing and a weights on my rear tire flew off , that just happened to me and i wanted to know if i can still drive this car intil i take it back monday? its a weekend i hate to have to sit in the house.


Add Reply

do you have wheel spacer lot of time wheel spacer do thin bounce you don't want or sometime you hit ah huge hole in the road that damage the wheel look for that too

Thecarphotoguy1
Aug 9th, 2008 @ 3:25 PM


“”
Replying to:

hey out there i just wanted to know if anyone ever had someplace do mounting and balanceing and a weights on my rear tire flew off , that just happened to me and i wanted to know if i can still drive this car intil i take it back monday? its a weekend i hate to have to sit in the house.

Goodyear Stores and most mechanic's shops will normally be able to mounting and balancing, but you can probably do some moderate driving until you get it done if it doesn't "bounce" too much...just get it done soon.

dapack69
Aug 9th, 2008 @ 1:02 PM


“”
Replying to:

hey out there i just wanted to know if anyone ever had someplace do mounting and balanceing and a weights on my rear tire flew off , that just happened to me and i wanted to know if i can still drive this car intil i take it back monday? its a weekend i hate to have to sit in the house.


Big Ten or FireStone should be open.



Advertise With GS!
 
Fuel your mustang love.
Leaderboards
gotstang owns

© 2004-2015 Gostang.com

All product names are the trademarks or registered trademarks of their respective companies

gotstang.com is not affiliated with Ford Motor Company