well i have less then 2 weeks left on deployment. here is my updated list of mods everything in red i have bought while on deployment:
Engine/Performance mods:
- 3.73 FRPP gears (at the shop getting reduced to 3.27 to support turbo kit)
- 11" Chrome moly Flywheel
- FRPP 31 Spline axle
- Centerforce Clutch & Kit w/ Pressure Plate
- Brand New t-45 Tranny
- MSD 8.5 Super Conductor Spark Plug Wire
- MSD Blaster Coils Packs
- Steel Re-in forced Brake Lines
- EBC Ceramic Brake Pads "red stuff"
- Power Master Battery
- Steeda Tri-ax Short Shifter
- Steeda Mil Eliminators
- Steeda Under drive Pulleys
- Steeda Oil Separator kit
- BBK Off Road X-pipe
- Energy Suspensions Polyurethane Engine mounts
- JLT TRU Cold Air Intake
- Flow master custom exhaust
- King Cobra Clutch Kit
- Yukon heavy duty axle
- Drilled and Slotted Rotors
- Ford Racing Shorty Headers
- Stage 8 titanium exhaust bolts
- SCE Pro Copper Exhaust Gaskets
- CANTON Racing Products Windage Tray Kit(not installed yet)
- Prothane Transmission mount
- SCT X-Calibrator 3
- CR1 Corbeau Microsuede seats (black) left and right
- 3" 5 point harness Corbeau (black) left and right
- adjustable lumbar left and right
- 5th slot addition both seats
- Corbeau seat tracks
- Nitto 305/35ZR-18 101Y B NT 555R Drag Radial (rear)
- Nitto 265/35ZR-18 93W B NT 555 Extreme Performance (front)
- CANTON Expansion Tank
Suspension Mods:
- MM adjustable rear lower control arms
- MM Front Coil Over Kit w/ hypersprings
- MM Rear Coil Over Kit w/ hypersprings
- MM panhard bar
- MM 4 point K-member brace
- MM full length sub-frame connectors
- MM 3 bolt caster/chamber plates
- MM pinion snubber
- Steeda X2 Balljoints
- Steeda Bumpsteer kit
- SteedaShockTower Brace
- Polyurethane Offset Rack Bushings
- Camber Adjustment bolt kit
- Polyurethane front and rear spring islolaters-
- Bilstein axle wrap shocks-
- Bilstein HD shocks and struts
- Eibach front sway bar(anti roll kit)
- Eibach rear sway bar(anti roll kit)
- Prothane bushings for sway bay
- H&R Race Springs
- Polyurethane exhaust hangers
- Lakewood upper control arms
Appearance mods:
- Steeda Shift knob
- Black lug nut set
- 8" shorty antenna
- White Cobra Stem caps-
- 3rd brake light "COBRA"
- FORD Skull insignia replacement
- GTS Smoked headlight covers
- Shaved bumper down 3 black with 2 clear coats on front
- Black Angel Eye Projectors
- Luminics Pure White H3 Mustang Light Bulbs
- Luminics Pure White 9005 Mustang Light Bulbs
- Altezza black tail lights
- American Muscle Rear Seat Delete kit
- Black FR500 (18x9) front
- Black FR500 (18x10) back
- Smoked Fog Lights
- Gray Cobra emblem trunk liner
- Saleen S281 style wing
- FRPP Competition Shift Light Tachometer
- Gen 2 Smoked Tail lights
here is what is happening to my rear end at CPR in Santee:
Yeah, we're going to rebuild traction lock. And when the new set of gears goes in with the install kit, the center of the rear end will be completely rebuilt. New clutches, gears(3.27's), bearing, shims on the carrier, and pinion seal. It's not going too bad. Had to send out the shocks. The coil over kit requires grooves cut into the shock to hold a ring for the coil over. So she has the lowers in right now and we're waiting for the grooves to be cut. We were told coil overs, but didn't realize they were this type. No biggie, just puts us behind waiting for machine work. Everything is going good so far though.
by the end of Sept she will have t-76 Hellion turbo kit on her with the 950 stroker assembly from MMR